Tie Rod Removal Tool

For all things chrome plated and greasy that don't mount to the truck

Moderator: Staff

Tie Rod Removal Tool

Postby itsmehb » Sat Aug 29, 2015 6:37 am

Recently replaced my tie rod ends. Anyone doing this may benefit from renting this tool from O'Riellys.
You do not have the required permissions to view the files attached to this post.
1990 Amigo, 2.3 5 speed (sold)
1991 Pick up (long gone)
2000 Amigo, 2.2 5 speed(sold)
1985 Trooper 1.9 4 speed (sent back to KS)
1989 Trooper RS 2.6 5 spd. Red

We get too soon old and too late smart!

"A true soldier fights not because he hates what is in front of him, but because he loves what is behind him"

Golf is just an expensive way to play marbles
User avatar
I am the Stig
Posts: 3866
Joined: Fri Jan 14, 2011 9:39 am
Location: Flower Mound Tx.
Has thanked: 142 times
Have thanks: 290 times


Re: Tie Rod Removal Tool

Postby Who is TJ » Sun Sep 13, 2015 10:52 pm

A few hits on the knuckle with a hammer would pop that tie rod right out! Just some advice in case you are ever in a jam.
1999 Isuzu Trooper LS. 3.5L Auto. 283,000 KM (175000 miles) and counting.
33" Hercules Mud Digger MT's
Surco Safari Rack custom fit.
6K HID Dual High and Low beam.
3"x3" Square LED fogs.
3" Total lift - Independent4X

View my build page: https://forum.planetisuzoo.com/viewtopic.php?t=79400

User avatar
Who is TJ
Drives in Mud
Posts: 86
Joined: Wed Sep 03, 2014 2:34 pm
Has thanked: 0 time
Have thanks: 5 times

Re: Tie Rod Removal Tool

Postby N law » Wed Sep 16, 2015 11:31 am

I have found a big hammer and a bigger hammer will pop tie rods loose. Use the bigger hammer on the backside of where the tie rod mounts up and the big hammer to whack the frontside. It will shock the tie rod right out.

For those who might have trouble following: if the tie rod stud is vertical, the hammer hits are horizontal on the spindle at the tie rod mounting hole.
99 VX
96 Rodeo Build thread
1975 FJ40
1990 Jeep Cherokee
69 Beetle
84 Westfalia
70 VW bus turned camper
07 Frontier V6 6 speed
1999 4Runner Limited
2018 4Runner Limited- wife's
2004 Genuine Stella Scooter
2018 GMC Sierra
User avatar
N law
Almost Joe Isuzu
Posts: 2783
Joined: Tue Aug 31, 2010 3:30 pm
Location: Chattanooga, TN
Has thanked: 17 times
Have thanks: 80 times

Re: Tie Rod Removal Tool

Postby Darby » Wed Sep 16, 2015 12:36 pm

Yeah, don't force it, get a bigger hammer.
Original owner of a 1993 Isuzu pick up, 2.3 engine, 5 speed with power steering and air conditioning. All original except the radio (still have factory radio).
It's cheaper to fix what you have than to buy someone else's problems.
Has a Trail Truck
Posts: 316
Joined: Sun Aug 10, 2014 6:42 pm
Location: Tampa Fl
Has thanked: 5 times
Have thanks: 22 times

Re: Tie Rod Removal Tool

Postby Von » Mon Mar 21, 2016 11:09 pm

LOL, I rented one of those yesterday. Tried to use it today and it's way too small, the little claw won't fit around the studs on my tie rods.
Might try the Double BFH approach.
2015 BMW 328i (The Mighty Wife's ride)
2009 Dodge Ram 1500 quad cab (my fat car with a yuge trunk)
1990 Trooper 2.8 V6 Auto (Wrecked... sent to the crusher)
1993 Shortbed, regular cab Z71 (Donated to step-son #2)(deceased, parted out)(Forums for GM and fullsize 4X4s suck... so I'm still hanging out here)
1965 Ford Fairlane 500 Sports Coupe 289 & 4 speed (SOLD)
1968 Kaiser M715, Ford 390, T18, Dodge divorced NP205, stock Dana 60 and 70 axles, lockers front and rear.
User avatar
Zu Royalty
Posts: 1348
Joined: Mon Dec 06, 2010 10:10 am
Location: Wichita Falls, Texas
Has thanked: 43 times
Have thanks: 43 times

Re: Tie Rod Removal Tool

Postby Beamer » Fri Apr 15, 2016 12:24 am

Just put new gears in the front end. Watched JohnnyFive's BFH technique on a youtube video. So i gave it a whirl, and it worked better than the pickle bar, or the pitman arm puller.
94 Rodeo, 115k on odo. 4x4, 5spd.
Changes; Indy4x HD torsion bars, OME springs, indy4x shackles, Indy4x ball joint flip/spacers, Warn hubs, sway bar bushings. New polyurethane boots for ball joints, and Mecatech boots for CV joints. Shock post extensions, shock boots, low profile bump stops.
BFG AT KO2 285/75/16, alloy wheels.
Regeared to 456, and front Lokka locker
Build thread; viewtopic.php?f=15&t=85242&p=753729#p753729

For this post the author Beamer was thanked by:
User avatar
Loyal P'up
Posts: 104
Joined: Wed Jan 28, 2015 8:50 pm
Location: Mill Creek, Wa
Has thanked: 13 times
Have thanks: 4 times

Return to Tool & Shop

Who is online

Users browsing this forum: No registered users and 1 guest